전체 글
-
멀티펑션테스터 - L 값 측정Parts 2022. 7. 21. 11:59
RLC 중 R 은 일반 테스터로 쉽게 측정할 수 있다. C도 어찌어찌 측정할 수 있다. 그런데 L은 측정이 쉽지 않다. 그래서 저항, 콘덴서, 코일의 값을 측정할 수 있는 테스터기를 알리에서 저렴한 가격으로 구입했다. R, L, C 와 함께 TR 과 D 도 측정할 수 있다. 테스터, 오실로스코프, 그리고 어떻게 구분해야 할지 잘 모를 Multi-Function-Tester (LCR Meter)를 가지고 있으면 도움이 될 듯 하다. 혹시나 저항값이 애매하거나 코일이나 콘덴서의 값을 확인하고 싶을때, TR 이 있는데 글씨가 잘 안보일때 등등 용도는 많을 듯 하다. 추가로 배터리 체크 기능과 IR 신호를 읽어서 파형으로 표시할 수 있다. 아쉽게도 콘덴서 측정 범위가 25pF 부터다. 10pF 이나 22pF 은..
-
칩저항 읽는 법 : EIA-96 사용방법카테고리 없음 2022. 6. 30. 01:21
칩 저항의 값을 읽는 방법들 1. 숫자 3개 사용 칩저항에 값을 쓰는 방식이 몇가지 있다. 그중 대표적인 방식은 3개의 숫자를 사용하는 방식이다. 471 471 은 47 x $10^{1}$ 을 의미한다. 330 ohm 이라면 33 x $10^{1}$ 이므로 331 로 쓰면 된다. [연습문제 ] 10 ohm ==> 10 x $10^{0}$ 이므로 100 으로 표시 10k ohm ==> 10,000 = 10 x $10^{3}$ 이므로 103 으로 표시 10 M ohm ==> 10,000,000 = 10 x $10^{6}$ 이므로 106 으로 표시 4.7 k ohm ==> 4700 = 47 x $10^{2}$ 이므로 472 으로 표시 2. 숫자 4개 사용 조금 더 자릿수를 늘려 정밀도를 높이는 표현방식도 있다..
-
STM32F103C6 기본 입출력 속도Arduino, nRF52, STM32, ESP32 2022. 5. 5. 16:39
아두이노 IDE 를 사용하여 STM32F103C6 보드의 기본 IO 속도를 측정해 본다. 기본 Blink 소스를 사용하되 delay 함수 없이 바로 ON/OFF 를 반복하게 하고 시간 간격을 오실로스코프로 측정한다. 아두이노 IDE 이용한 기본 소스 void setup() { pinMode(PC13, OUTPUT); } void loop() { digitalWrite(PC13, HIGH); // turn the LED on (HIGH is the voltage level) digitalWrite(PC13, LOW); // turn the LED off by making the voltage LOW } 기본소스는 delay 없는 blink 이고 이때의 오실로스코트 기록은 다음과 같다. 코드의 기본 구조는 ..
-
STM32F103C6 사용법Arduino, nRF52, STM32, ESP32 2022. 5. 5. 16:09
이전글에서 STM32F103C8 보드에 대한 아두이노 IDE 사용법을 기록하였다. 이번 글에서는 STM32F103C6 에 대한 사용법을 기록한다. 첫째, C8 처럼 마이크로 USB 를 이용한 접속은 안된다. ST-LINK 를 이용해서 프로그램을 업로드한다. 아때 아두이노 IDE 의 설정은 다음과 같다. 보드에서 STM32F103C6/fake STM32F103C8 을 선택한다. 업로드방법은 STLink 를 선택한다. 나머지는 이전 글과 동일하다. 2022.04.25 - [Arduino, nRF52, STM32, ESP32] - STM32 보드에 아두이노 IDE 를 사용하기
-
OP Amp 와 Comparator 차이Parts 2022. 5. 5. 11:18
OP Amp (연산증폭기) Operational Amplifier(연산 증폭기)의 약자로 고입력저항, 저출력 저항, 고개방 이득(Open Loop Gain)을 가지고 +입력단자(비반전 입력단자)와 -입력단자(반전압 입력단자) 간의 전압 차이를 증폭하는 기능을 갖는 차동증폭기이다. OP Amp는 1회로 당 1)정측 전원 단자, 2)부측 전원 단자, 3)+입력 단자, 4)-입력 단자, 5)출력 단자로 구성된다. 입력 신호원 Vs, 신호원 출력 저항 Rs, OP Amp 의 입력 저항 Ri , OP Amp 의 출력 저항 Ro , 부하 저항 Rl, OP Amp 의 증폭률 Av 일때 입력전압 Vs 와 출력 전압 Vo 의 관계는 다음과 같습니다. Vo = (Ri/(Ri+Rs))*Vs * (Rl/(Rl+Ro))*Av ..
-
STM32 보드에 아두이노 IDE 를 사용하기Arduino, nRF52, STM32, ESP32 2022. 4. 25. 09:19
STM32 "Blue Pill" 개요 이 보드는 공식 Arduino 보드에 비해 저렴하며 하드웨어 역시 오픈 소스이다. 보드는 RTC(실시간 클록)를 구동하는 데 사용할 수 있는 2개의 수정 발진기(8MHz 수정 1개와 32KHz 수정 1개)를 가지고 있다. MCU는 딥 슬립 모드에서 작동할 수 있어 배터리 구동 애플리케이션에 적합하다. 이 보드를 프로그래밍하려면 간단한 USB-UART 변환기를 사용하면 되고, PC에서 USB를 이용하여 프로그래밍할 수 있다. 아래쪽 4개의 핀이 각각 3.3V, SWDIO, SWCLK, GND 이다. 일반적으로 이 4개의 핀을 이용하여 ST-LINK 에 연결한다. 사용한 ST-LINK 의 버전은 v2 이며 현재 v3가 판매중이다. I. 보드에 부트로더 업로드 처음으로 할..
-
라인센서 감도에 사용되는 색온도 정보LinearImageSensor 2022. 4. 9. 17:47
빛의 정도를 측정하는 표준 라인센서를 사용하다보면 결국 라인센서에 들어오는 빛의 정도를 측정하게 된다. 이때 측정되는 빛과 그림자의 정도를 수치로 표시하게 되는데 빛이 어떤 것이 들어오는지에 따라 달라지게 된다. 이를테면 선글라스를 낀 눈, 돋보기를 낀 눈, 적외선 필터를 안경으로 낀 눈에 들어오는 빛이 달라지는 것과 같다. 라인센서는 자체적으로 일정한 빛을 받아들이고 그 정도를 측정한다. 이때 2854K 를 종종 보게 된다. 이에 대한 간략한 설명을 아래에 첨부한다. 우리나라의 공업 규격에서도 국제조명위원회 규정을 적용한다(KS 0064). 표준 광원에는 A, B, C, D, F 가 있고, 이는 추후 추가될 수 있다. 표준광A : 가스충전 상태의 텅스텐 백열전구를 기준으로 하며 그 색온도는 2854K이..